Industry Directory | Consultant / Service Provider
EDA-US, Inc. is a one stop shop for your design needs. From schematic capture to prototype development, EDA-US looks forward to working with you. For a quote or more information please email sales@eda-inc.us
Affordable Manufacturing Execution System (MES), Shop Floor Automation and Integration Software CELLS WORKFLOW Product Tracking MES is an affordable full Manufacturing Process Control Software System providing Plant Intelligence for any industry.
The DV-03 is a air-actuated balanced spool valve for consistent dispensing of high viscosity fluids. For precision, you can control the amount of fluid dispensed by adjusting the fluid pressure, pulse time, and selecting the appropriate dispense tip
Electronics Forum | Wed Dec 07 20:51:59 EST 2022 | proy
cut time was very good (not a concern) Main advantage is flexibility and simpler fixturing than routing as there are no side forces. Charing was evident, but can be reduced with a few tweaks.
Electronics Forum | Thu Aug 31 04:25:03 EDT 2000 | Chris May
Dougie, If you have square, rectangular etc; shaped PCB's maybe you could have routing between circuits. "V" shaped grooves top and bottom. I found this extremely good especially if the assemblies are wave soldered. No gaps for flowing up and over.
Industry News | 2010-09-02 16:09:40.0
Each step in the electronics assembly process will be on display and fully functioning on the show floor at Electronics Midwest, produced by IPC — Association Connecting Electronics Industries® and Canon Communications.
Industry News | 2007-12-06 11:45:48.0
Solid Copper Conductors are Added Between BGA Pads
Technical Library | 2019-05-15 22:26:02.0
As the demand for higher routing density and transfer speed increases, Via-In-Pad Plated Over (VIPPO) has become more common on high-end telecommunications products. The interactions of VIPPO with other features used on a PCB such as the traditional dog-bone pad design could induce solder joints to separate during the second and thereafter reflows. The failure has been successfully reproduced, and the typical failure signature of a joint separation has been summarized.To better understand the solder separation mechanism, this study focuses on designing a test vehicle to address the following three perspectives: PCB material properties, specifically the Z-direction or out-of-plane Coefficient of Thermal Expansion (CTE); PCB thickness and back drill depth; and quantification of the driving force magnitude beyond which the separation is due to occur.
www.unisoft-cim.com/cells.html - CELLS WORKFLOW is affordable, simple to setup & use yet powerful product & job tracking software for fast New Product Introduction (NPI). The CELLS WORKFLOW software provides total traceability in manufacturing floor
http://paceworldwide.com/products/conductive-rework-systems/prc-2000/prc-2000-pace-repair-center-the-benchtop The PRC 2000 Benchtop Factory is the ultimate rework center. The PRC 2000 can tackle just about any Thru-Hole, SMT application and is well
Career Center | Savannah, Georgia USA | Engineering,Human Resources,Maintenance,Management,Production,Quality Control,Research and Development,Technical Support
I’d like to give you a brief overview of my skills and experience. I am confident that I could bring value to the SMTnet as your Safety Professional. Here’s how my qualifications meet your requirements: • Military (E-7) Manager with experience as
Career Center | RACINE, Wisconsin USA | Sales/Marketing
Business Development Leader • Experienced business leader in-depth knowledge in techincal industries, candid communicator. • Expertise in building and expanding client base, increasing name recognition and market share using a wide array of tools,
Shear Force Heller Industries The increasing awaren
SMTnet Express, September 16, 2021, Subscribers: 26,691, Companies: 11,438, Users: 26,841 Mathematical Model For Dynamic Force Analysis Of Printed Circuit Boards Mathematical model for dynamic force analysis of printed circuit
PCB Libraries, Inc. | https://www.pcblibraries.com/forum/footprint-land-pattern-naming-convention_topic29_post1963.html
:21am If I understand correctly, I should always create my footprints in metric. In case of a 2.54mm pin spacing (converted parts) I should use a routing grid of
| https://www.smtfactory.com/I-C-T-L12-LED-Nitrogen-Reflow-Wave-Oven-SMD-Heating-pd41529734.html
Robot Dispensing Robot Routing Robot SMT Peripheral Equipments Consumables Solder Bar Solutions LED Industry Communication Automotive Electronics Medical Instrument Smart Home Appliances Industrial
